操作方法と安全データ

Light-curing resin operating instructions and safety data

The complete process

01.

printing

02.

Washing

03.

Drying

04.

Post-curing

印刷

まず、スライスソフトウェアで使用する3Dプリンターを選択し、個人の状況や要求に応じて適切な印刷データを修正します。最後に、印刷物の配置やサポートを整え、スライスして3Dプリンターにセットします
（初めて使用する場合は、上記の印刷設定やテストファイルを参考にしてください）

Washing

After printing is complete, the print is soaked in alcohol to clean it and achieve a clean finish.

Drying

After cleaning, the print should be thoroughly dried using a fan, air pump, spray gun, or air drying. If the print is still sticky or has obvious resin marks after drying, repeat the cleaning and drying steps again.

sla_guide_1.jpg__1354x0_q85_subsampling-2.jpg

Yellowing issues after post-curing of prints?
1. Bake at 50°C for 2 hours.
2. Leave the product in a room out of direct sunlight. The yellowing will improve visibly in 3 days, and it will become transparent in about a week.

二次硬化

印刷物の表面が乾燥し、明らかな樹脂の跡がない場合、405nm波長の紫外線を使用して二次硬化を行います。通常は5〜10分間、印刷物の形状、機器の出力、関連設定に応じて異なります

Safety and Precautions

Please note!

Precautions for use

Please use and store this resin at room temperature in a dark, well-ventilated place.
Before using the resin, shake it evenly.
Store used resin in a light-opaque container and do not mix with new material.
Keep this material out of reach of children and out of direct sunlight.
Wear gloves and a mask when handling the product. If resin comes into contact with skin or eyes, wash immediately with plenty of water.
It is prohibited to dispose of this material at will. If disposal is necessary, please solidify the material and recycle the solid as "general recyclable material."

caveat

May cause skin irritation
May cause serious eye irritation
May cause respiratory irritation
May have long-term harmful effects on aquatic life
Avoid release into the environment
If on skin: Wash with plenty of soap and water.
Eye contact: Rinse cautiously with water for several minutes. Remove contact lenses (if possible). Continue rinsing.

Otomosin

Otomo Resin

Light-curing resin operating instructions and safety data

The complete process

printing

Washing

Drying

Post-curing

印刷

Washing

After printing is complete, the print is soaked in alcohol to clean it and achieve a clean finish.

Drying

After cleaning, the print should be thoroughly dried using a fan, air pump, spray gun, or air drying. If the print is still sticky or has obvious resin marks after drying, repeat the cleaning and drying steps again.

Yellowing issues after post-curing of prints?
1. Bake at 50°C for 2 hours.
2. Leave the product in a room out of direct sunlight. The yellowing will improve visibly in 3 days, and it will become transparent in about a week.

二次硬化

印刷物の表面が乾燥し、明らかな樹脂の跡がない場合、405nm波長の紫外線を使用して二次硬化を行います。通常は5〜10分間、印刷物の形状、機器の出力、関連設定に応じて異なります

Safety and Precautions

Please note!

Precautions for use

Please use and store this resin at room temperature in a dark, well-ventilated place.

Before using the resin, shake it evenly.

Store used resin in a light-opaque container and do not mix with new material.

Keep this material out of reach of children and out of direct sunlight.

Wear gloves and a mask when handling the product. If resin comes into contact with skin or eyes, wash immediately with plenty of water.

It is prohibited to dispose of this material at will. If disposal is necessary, please solidify the material and recycle the solid as "general recyclable material."

caveat

May cause skin irritation

May cause serious eye irritation

May cause respiratory irritation

May have long-term harmful effects on aquatic life

Avoid release into the environment

If on skin: Wash with plenty of soap and water.

Eye contact: Rinse cautiously with water for several minutes. Remove contact lenses (if possible). Continue rinsing.

Contact Us - Otomo Resin

Otomo Resin

Light-curing resin operating instructions and safety data

The complete process

printing

Washing

Drying

Post-curing

印刷

Washing

After printing is complete, the print is soaked in alcohol to clean it and achieve a clean finish.

Drying

After cleaning, the print should be thoroughly dried using a fan, air pump, spray gun, or air drying. If the print is still sticky or has obvious resin marks after drying, repeat the cleaning and drying steps again.

Yellowing issues after post-curing of prints? 1. Bake at 50°C for 2 hours. 2. Leave the product in a room out of direct sunlight. The yellowing will improve visibly in 3 days, and it will become transparent in about a week.

二次硬化

印刷物の表面が乾燥し、明らかな樹脂の跡がない場合、405nm波長の紫外線を使用して二次硬化を行います。通常は5〜10分間、印刷物の形状、機器の出力、関連設定に応じて異なります

Safety and Precautions

Please note!

Precautions for use

Please use and store this resin at room temperature in a dark, well-ventilated place.

Before using the resin, shake it evenly.

Store used resin in a light-opaque container and do not mix with new material.

Keep this material out of reach of children and out of direct sunlight.

Wear gloves and a mask when handling the product. If resin comes into contact with skin or eyes, wash immediately with plenty of water.

It is prohibited to dispose of this material at will. If disposal is necessary, please solidify the material and recycle the solid as "general recyclable material."

caveat

May cause skin irritation

May cause serious eye irritation

May cause respiratory irritation

May have long-term harmful effects on aquatic life

Avoid release into the environment

If on skin: Wash with plenty of soap and water.

Eye contact: Rinse cautiously with water for several minutes. Remove contact lenses (if possible). Continue rinsing.

Contact Us - Otomo Resin

Yellowing issues after post-curing of prints?
1. Bake at 50°C for 2 hours.
2. Leave the product in a room out of direct sunlight. The yellowing will improve visibly in 3 days, and it will become transparent in about a week.